Audio Recording

HotStepper is a drum arranger, composer and sequencer that is free to use. This software runs very well in Windows environment. To try this software; download it at this URL. The download package is a .zip file. Right click on this zip file and then click “Extract here”. This is standalone software which means you do not this to be installed in your Windows operating system. After unzipping, go inside hotstepper folder. The executable file of this software is HotStepper.exe. There are other files that are inside this folder and do not delete or edit them. To launch this sequencer, double click HotStepper.exe. You should then see the default sequencer window such as shown below:

To use it, it is really easy. All you need is to click on the blue regions and it will leave a red triangle on the marked region. To play what you have composed, click “Loop Solo”. If you commit a mistake simply right click over the red triangle and it will be removed.

What is good with hotstepper is the ability to create both simple and advanced drum loops. But it will take time to master the hotstepper drum looping skills. I suggest you will practice it on a daily basis and incorporate the created loops in your recording project.

Now here is one of the main problems, you might notice that HotStepper includes a default set of drum sounds in its sound library. These sounds are not taken from actual acoustic drum sounds. One big advantage is that you can enhance its sound library with the new set of drum sounds. With real drum sounds in the sound library, you won’t anymore need a complete drum set or a drummer to produce the drum tracks in your project. All you need to do is to compose your favorite drum loops using this software, export it as wav to your DAW then it’s done.

To add new sets of drum sounds in the library, follow these steps:

1.) Record actual drum sounds from each component using a microphone. Save it as snare.wav, cymbals.wav; etc for the rest of the drum parts. You can record at 24-bit/96Khz mono for best resolution. Make sure it was the best recording possible and ensure that it don’t clip. Back up these audio files, so that you will not need to record again in this case you made an mistake in formatting the sound file (in step#2).

You need to format each sound clip from each drum parts so that it will fit with the HotStepper sound library. The acceptable format is: 44100Hz, 16-bit mono and each drum sound sample should be less than 10 seconds.

2.) To start formatting, open each of the drum sound clips with your recording software and then trim down the sound clip to the following recommended audio length:

a.) Snare – 0.965 second

Length is measured from the start to end of the sound clip. Make sure the audio recording immediately start at 0 second. See screenshot below:

b.) Crash cymbal – 5.107 seconds
c.) Tom – 0.608 second
d.) Kick – 0.915 second
e.) Side stick – 0.850 seconds
f.) Ride cymbal- 1.709 seconds
g.) Pedal hi hat- 0.136 seconds
h.) Open hi hat- 2.092 seconds
i.) Mid-tom- 2.589 seconds
j.) Floor tom- 2.793 seconds

3.) Save the edited drum sound clip as 44100Hz, 16-bit mono.
4.) Launch HotStepper and then go to View – Sound Library.
5.) Click “Add Sound” then click “Load Wave”. You can only load one drum sound clip at a time. Select the audio file and then click “Open”. For example, I select the edited “toom.wav” and I would like to add it to the library. This is how it looks like after clicking “Open”:

You can click the play button to preview. If everything is OK, click “Add” then “Close”. You will then see the sound clip listed in the sound library:

To update the list; click “Close and Save” button in Sound Library; then go to File – Quit. If it asks “Do you want to save before continuing?” click “No”. Re-launch Hotstepper and then you will now see toom.wav listed as one of the Hotstepper drum library sound. If you do not see it, right click on the gray area, then you see the “Select Sound”. See screenshot: